G. I. Raab

Nosov Magnitogorsk State Technical University — Russia

Materials Science · Physical Sciences

30h-index3.6kcitations248works0.32yr avg
OpenAlex↗ORCID↗Google Scholar↗Lab page↗

Accepting Students?

No reports yet. Know if this professor is taking students?

Research Topics

Microstructure and mechanical properties(155), Metallurgy and Material Forming(62), Aluminum Alloys Composites Properties(51), Advanced materials and composites(49), Microstructure and Mechanical Properties of Steels(45)

Publications247 total

Transformation of the Structure and Properties of Cu-11Sn Alloy Subjected to Asymmetric Rolling
Transactions of the Indian Institute of Metals·2025
Stabilization of Roll Speed Mismatch in Controlled Asymmetric Rolling
Journal of Physics Conference Series·2025Open Access
Mechanical Properties of Ultrafine-Grained Aluminum Bronze at High Deformation Rates
Metal Science and Heat Treatment·2025
Increasing Technological Plasticity of Low-Carbon Steels in the Process of Asymmetric Cold Rolling
Springer proceedings in physics·2025
Effect of Asymmetric Rolling on the Structure and Properties of Cu-Cr-Zr Alloys
Physical Mesomechanics·2024· 2 cited
EFFECT OF ASYMMETRIC ROLLING ON THE STRUCTURE AND PROPERTIES OF CU-CR-ZR ALLOYS
Fizicheskaya Mezomekhanika·2024
Structure and properties of the contact wire obtained by ECAP with forming
Journal of Metals Materials and Minerals·2023Open Access
Deformation Behavior under Tension with Pulse Current of Ultrafine-Grain and Coarse-Grain CP Titanium
Materials·2022· 11 citedOpen Access
Finite Element Analysis of the Stress–Strain State of the Deformation Zone of a Workpiece from UFG Grade 4 Ti Subjected to Abrasive-Free Ultrasonic Finishing
Russian Journal of Non-Ferrous Metals·2022
Microstructural evolution during superplastic deformation of Al-Mg-Li alloy: Dynamic recrystallization or grain-boundary sliding?
Journal of Alloys and Compounds·2022· 19 cited
Finite element analysis of stress-strain state of the deformation zone of a UFG TI Grade 4 workpiece subjected to abrasive-free ultrasonic finishing
Izvestiya Non-Ferrous Metallurgy·2022
Microstructure, Mechanical and Superelastic Properties of Ti-Zr-Nb Alloy for Biomedical Application Subjected to Equal Channel Angular Pressing and Annealing
Metals·2022· 4 citedOpen Access
Regularities of Microstructure Evolution in a Cu-Cr-Zr Alloy during Severe Plastic Deformation
Materials·2022· 20 citedOpen Access
The formation of a high-strength state in martensitic Ti Grade 4 by ECAP
Journal of Alloys and Compounds·2022· 24 cited
Influence of High-Speed ECAP on the Structure and Properties of Copper and Copper Alloy of Cu-Cr System
Key engineering materials·2022
Superplastic‐Like Behavior and Enhanced Strength of a Two‐Phase Titanium Alloy with Ultrafine Grains
Advanced Engineering Materials·2022· 6 cited
Roughness and microhardness of UFG Grade 4 titanium under abrasive-free ultrasonic finishing
Frontier materials & technologies·2022· 1 citedOpen Access
Microstructural Evolution During Superplastic Deformation of Al-Mg-Li Alloy: Dynamic Recrystallization or Grain-Boundary Sliding?
SSRN Electronic Journal·2022Open Access
Effect of the Type of Crystal Lattice of Metals on Structure Formation and Mechanical Properties Under Plastic Shear Deformation
Metal Science and Heat Treatment·2022· 1 cited
The study of influence of temperature and speed conditions on the mechanical properties of bioresorbable Zn–4Ag–Cu zinc alloy during equal-channel angular pressing
Frontier materials & technologies·2022· 4 citedOpen Access
page 1 of 13Next →

Frequent Co-authors

Р. З. Валиев(24), С. В. Добаткин(11), Yuri Estrin(8), Д. В. Гундеров(6), Irina P. Semenova(6), Natalia Martynenko(6), V. N. Serebryany(6), Yuntian Zhu(5), Alexander P. Zhilyaev(5), Terence G. Langdon(5), N. Yu. Anisimova(5), Terry C. Lowe(4), Nariman A. Enikeev(4), E. A. Luk’yanova(4), O. V. Rybalchenko(4), Mikhail Kiselevskiy(4), V. V. Stolyarov(4), A. Polyakov(3), Anna Churakova(3), G.A. Salishchev(3)